FDISK(8)

NAME
fdisk - partition table maintenance program

SYNOPSIS
fdisk [-evy] [-A | -g | -i | -u] [-b blocks[@offset[:type]]] [-l blocks | -c cylinders -h heads -s sectors] [-f file] disk
fdisk -R [-y] disk [file]

DESCRIPTION
fdisk creates and edits MBR and GPT partition tables. These tables are used by the boot process of some platforms to find the OpenBSD kernel and, when present, are used by the kernel to find the disklabel(5).

Caution is advised when editing these tables since some platforms rely on specific configurations created at install time.

The options are as follows:

-A  Modifies the GPT partition table entries on disk to put all available space not taken by -b into a single OpenBSD partition. The available space is maximized by deleting all existing partition entries except for partition types APFS ISC, APFS, APFS Recovery, BIOS Boot, HiFive FSBL, HiFive BBL and partitions with the ‘Required’ GPT attribute set.

    If APFS ISC, APFS, or APFS Recovery partitions are detected then existing EFI system partitions are also preserved. If the preserved EFI system partition has fewer blocks than the number requested with -b, the modified GPT is discarded.

-b blocks[@offset[:type]]
    Creates a partition table entry of the specified number of blocks, offset and type. offset defaults to the first available block, and type defaults to ‘EF’.

    -b is only available in combination with -A, -g, or -i.

    If -A or -g is specified, only the blocks value is used.

    -c cylinders -h heads -s sectors Specifies a geometry for fdisk to use. By default the disk size and geometry are obtained from the default disklabel(5) constructed by the kernel for disk. See disklabel(5) and disklabel(8).

-e  Invokes the interactive partition table editor. See COMMAND MODE below.

-f file
    Specifies a file containing the bootcode for an MBR. The default file is /usr/mdec/mbr.

-g  Writes a default GPT, including a protective MBR, to disk. The GPT has a single OpenBSD partition containing all available space not taken by -b.

-i  Writes a default MBR to disk. The MBR has a single OpenBSD partition containing all the available space not taken by -b. The bootcode is initialized as described in -u.

-l count
    Treat disk as though it has a size of count blocks.

-R disk [file]
    Creates a GPT or MBR partition table based on the contents of file. file contains the output of fdisk -v (e.g. the fdisk* files in /var/backups) or compact GPT partition descriptions of the form

        <id>:<type>[<start>:<size>]<attributes><name>

    where a new partition UUID is always generated and <attributes><name> is optional. For example:

        0: EFI Sys [64:66560] 0x0 EFI System Area

    If <start> is 0 it is set to the first usable LBA of the largest chunk of free space.

    If file is not provided, fdisk attempts to fully restore a GPT if either a primary or secondary GPT exists on disk.

-u  Updates the MBR bootcode. If a bootcode file is present (see -f) the MBR, except for the partition entries, is replaced by the first block of the file. If no bootcode file is present, zeros are used.

    Not available when editing a GPT.

-v  Prints detailed information about the MBR, the Primary GPT and the Secondary GPT.

-y  New or modified partition table is written to disk without asking for confirmation.

disk
    fdisk creates or modifies the partition table of disk. disk can be a full pathname, e.g. /dev/rsd0c, a raw partition name, e.g. sd0c, or just the disk name, e.g. sd0.

TYPICAL LAYOUT
When called without options, fdisk prints the partition table of disk.

If disk has a GPT a terse version of its contents is printed:

    # fdisk sd0
    Disk: sd0	Usable LBA: 64 to 500118128 [500118192 Sectors]
       #: type                                 [       start:         size ]
    ------------------------------------------------------------------------
       1: EFI Sys                              [          64:          960 ]
       3: OpenBSD                              [        1024:    500117105 ]

When disk does not have a GPT, the first block of disk is printed as an MBR:

    # fdisk sd0
    Disk: sd0	geometry: 121601/255/63 [1953525168 Sectors]
    Offset: 0	Signature: 0xAA55
               Starting       Ending      LBA Info:
     #: id     C  H  S -      C   H  S [     start:       size ]
    ------------------------------------------------------------------------
     0: 0B     0  1  1 -  26108   0 63 [        63:  419425020 ] FAT32
     1: 00     0  0  0 -      0   0  0 [         0:          0 ] unused
     2: 00     0  0  0 -      0   0  0 [         0:          0 ] unused
    *3: A6 26108  1  1 - 121600 254 63 [ 419425083: 1534094982 ] OpenBSD

NOTE: Partition entry #3 of this MBR is flagged as bootable.

NOTE: The S field in the C/H/S values is “1 based”, but the LBA "start" field is “0 based”.

The -v option causes more information to be printed:

    # fdisk -v sd0
    Primary GPT:
    Disk: sd0	Usable LBA: 64 to 500118128 [500118192 Sectors]
    GUID: f0418899-4976-4604-a783-3ebe135a8f12
       #: type                                 [       start:         size ]
          guid                                 name
    ------------------------------------------------------------------------
       1: EFI Sys                              [          64:          960 ]
          d0834013-dab8-44df-a5e4-123148f17e03 EFI System Area
       3: OpenBSD                              [        1024:    500117105 ]
          cd356d77-8369-44b4-996e-79e8b9a47bfe OpenBSD Area
    Secondary GPT:
    Disk: sd0	Usable LBA: 64 to 500118128 [500118192 Sectors]
    GUID: f0418899-4976-4604-a783-3ebe135a8f12
       #: type                                 [       start:         size ]
          guid                                 name
    ------------------------------------------------------------------------
       1: EFI Sys                              [          64:          960 ]
          d0834013-dab8-44df-a5e4-123148f17e03 EFI System Area
       3: OpenBSD                              [        1024:    500117105 ]
          cd356d77-8369-44b4-996e-79e8b9a47bfe OpenBSD Area
    MBR:
    Disk: sd0	geometry: 31130/255/63 [500118192 Sectors]
    Offset: 0	Signature: 0xAA55
                Starting         Ending         LBA Info:
     #: id      C   H   S -      C   H   S [       start:        size ]
    -------------------------------------------------------------------------------
     0: EE      0   0   2 -  31130 233  63 [           1:   500118191 ] EFI GPT
     1: 00      0   0   0 -      0   0   0 [           0:           0 ] unused
     2: 00      0   0   0 -      0   0   0 [           0:           0 ] unused
     3: 00      0   0   0 -      0   0   0 [           0:           0 ] unused

COMMAND MODE
When fdisk enters interactive command mode, it copies the partition table from disk into memory and performs all edits on that copy. The partition table on disk is modified only by write or quit commands.

The prompt contains information about the state of the edit process.

    disk*:1>

Where disk is the name of the disk being edited, ‘*’ means that the partition table has been modified, but not yet written to disk and 1 is the edit level when operating on the MBR or GPT. This number is 2 when editing an extended partition in the MBR, 3 when editing an extended partition within the edit level 2 extended partition, and so on.

The list of commands and their functions is given below. Commands may be abbreviated. The first command matching the abbreviation is selected.

?   A synonym for help.

help
    Displays a short summary of available commands.

manual
    Displays this manual page.

reinit [gpt | mbr]
    Initializes the partition table.

    By default an MBR partition table is initialized. If gpt is specified a GPT partition table is initialized, including the protective MBR.

setpid #
    Sets the identifier of the partition table entry.

edit #
    Edit an entry in the partition table. The offset and size of the entry may be specified in CHS mode (MBR only), by using sector offsets and sizes, or by using the units ‘b’, ‘k’, ‘m’, ‘g’, or ‘t’ to indicate bytes, kilobytes, megabytes, gigabytes, or terabytes. The special size value ‘*’ causes the partition to be sized to use the remainder of the disk.

flag # [value]
    Set the partition's flag (MBR) or attribute (GPT) value. value can be a positive integer or a hex string. An MBR partition will accept values from 0 to 0xff. A GPT partition will accept values from 0 to 0xfffffffffffffff. If value is not provided, the partition's bootable flag is set and all other partitions have their bootable flags reset. MBR partitions with the bootable flag set are printed with a ‘*’ prefix. GPT partitions with the bootable flag set display 'bootable' in their attributes list.

update
    Updates the MBR bootcode. If a bootcode file is present (see -f) the MBR, except for the partition entries, is replaced by the first block of the file. If no bootcode file is present, zeros are used.

    Not available when editing a GPT.

select #
    Selects an extended partition entry, increasing the edit level by 1.

    Not available when editing a GPT.

swap # #
    Swaps two partition entries.

print [unit]
    Prints the partition table. If unit is ‘b’, ‘k’, ‘m’, ‘g’, or ‘t’ partition sizes are shown in bytes, kilobytes, megabytes, gigabytes, or terabytes. If unit is not provided, sizes are shown in sectors.

write
    Writes the partition table to disk.

exit
    Discards outstanding changes and exits the current edit level. If the edit level is 1, fdisk terminates.

quit
    Writes outstanding changes to disk and exits the current edit level. If the edit level is 1, fdisk terminates.

abort
    Discards outstanding changes and terminates fdisk.

FILES
/usr/mdec/mbr
    default MBR bootcode

SEE ALSO
disklabel(5), boot(8), boot_amd64(8), boot_i386(8), boot_macppc(8), disklabel(8)